6 Types of Basement Floor Drains
Getting rid of water in a basement with persistent flooding issues is a special kind of problem. Here are six of the most common ways to address it.
ROBIN GENTRY/GETTY IMAGES
Choosing a Basement Floor Drain
It’s rare to find a basement that doesn’t experience issues with moisture. When excessive moisture or active leaking results in standing water on the floor, the integrity of the building and the health of the people living in it are at risk.
Current building codes mandate the installation of a basement drainage system in new construction, but plenty of houses predate this requirement. If your basement is one of them, you have options for adding drainage.
Sometimes, it’s best to install outdoor drains to direct water away from the foundation. If they’re deep enough, they can also relieve hydrostatic pressure from rising groundwater. More often than not, however, exterior drainage must be supplemented by a basement floor drain.
The best choice for you will depend on the characteristics of the basement floor and the path the water takes to get into the basement. Water that seeps in through the walls can often be diverted by a perimeter drain. But water pushing its way in from underneath may call for a more extensive system that runs across the middle of the floor.
Once you channel the water to a central point, you still have to get it outside. That usually takes a sump pump, which may send water into the building’s waste system or outside to a safe runoff location.
Floor drains are always installed flush with the surface, which involves digging, no matter which type you choose. If your basement has a concrete floor, a certain amount of demolition may also be involved. It may make sense to pour new concrete to create a finished floor surface that slopes toward the drain.
Here’s a list of common floor drain systems, and the conditions under which each works best.
jada photo/Getty Images
This consists of a gravel-embedded perforated pipe installed in a trench that slopes toward a drainage point. It’s a good solution for flooding caused by groundwater. Typically installed six to 24 inches deep, it can also control water seepage through walls.
This type is sometimes called drain tile because it was made from old roofing tiles in the days before plastic pipes. The gravel is usually left exposed at the floor surface, but you can cover it with a metal or plastic grid if you choose.
VEX Collective/Getty Images
This is so similar to a French drain that the two are often confused. The difference? A curtain drain is shallower.
It consists of perforated pipe embedded in gravel and installed in a sloping trench. The shallow placement allows the drainage pipe to catch and redirect water seeping in through the walls.
Because you don’t dig it as deep, a curtain drain is easier to install than a French drain. It can be an adequate drainage solution when groundwater flooding isn’t likely.
Channel or Trench Drain
This is simply a sloping trench covered by a metal grid, installed around the floor perimeter or in the middle of the floor. It doesn’t soak up water; it directs it to a sump pit or some another place where it can drain safely. It provides insurance against flooding from plumbing leaks and similar accidents.
The basement floor must slope toward a channel drain, so the trench is usually dug at the lowest point. Installation may necessitate resurfacing the floor to give it the necessary slope.
Linus Strandholm/Getty Images
Standard Floor Drain
Perhaps the most familiar of all basement drains, the standard floor drain features a round or rectangular grid covering the hole. It sits at the lowest part of the floor, collecting standing water that comes in through the walls or elsewhere. It sends the water through an underground pipe to the plumbing system or to a sump pit.
If it connects to the plumbing, this type of drain is best installed during initial construction, because it needs a P-trap and vent to prevent the release of sewer gases into the basement. Piping a floor drain into a sump pit avoids such complications.
Robin Gentry/Getty Images
Sump Pit and Sump Pump
A sump pump and sump pit are often used in conjunction with another drainage network. But even without supplemental drainage, a sump system can effectively protect a basement from flooding due to a high water table.
Groundwater flows into the sump pit, dug below the floor. When it rises to a dangerous level, the pump switches on to empty the pit. Sump pumps are commonly found in basements built in poorly draining soil or low-lying areas subject to flooding.
Sveta Kroitor/Getty Images
Exterior Perimeter Drain
Exterior drains installed around the perimeter of the foundation collect and redirect water before it seeps into the basement. In locations with high groundwater or heavy runoff, they’re often French drains dug along the foundation wall or even at its base. When runoff is the only issue, a channel drain may do the job.
Sometimes an exterior drain is all a basement needs to stay dry. But in locations with high groundwater, they’re only part of a complete drainage system.